5V/12V 2/3/4 Button Timer Delay Relay Motor Speed Temperature Controller+Buzzer

• Popularity - 2166 views, 309.4 views per day, 7 days on eBay. Super high amount of views. 7 sold.
• Price - Avg: $0.00, Low: $0.00, High: $0.00. Best quality when compared to PicClick similar items.
• Seller - + items sold. 0% negative feedback. Great seller with very good positive feedback and over 50 ratings.

Visit store<br>Items for sale<br>About us<br>Product Details<br>1.Digital Display Delay Controller：（DC 12V with Buzzer 2 Button<br>)<br>Product parameters<br>Working voltage: DC12V (normal working voltage DC10V-16V)<br>Signal source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)<br>Output capability: It can control devices within 30v5A or within 220v5A<br>Quiescent current:<br>20mA, working current: 50mA<br>Service life: more than 100,000 times;<br>Working temperature: -40~85 °C;<br>Net weight: about 26g<br>Size: 64.2mm*34.8mm*18.5mm<br>Features<br>Voltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.<br>Function introduction<br>When the power is turned on, the trigger signal is received, the countdown starts, and the relay works. When the timer ends, the relay stops working, the time returns to the setting, and the next trigger signal is waited.<br>Instructions<br>1).Press K1 to enter the time setting, the hundred digit digital tube starts to flash; press K2 at this time, the hundred digits change; press K1 again, the ten digital tube starts to flash; press K2 at this time, the ten digits change; press again After K1, the digital tube starts to flash. At this time, press K2, the digit of the digit changes; press K1 again to exit the setting, and the digital tube no longer flashes.<br>2).When the digital tube is normally displayed, press K2, the decimal point is shifted, the decimal point is 0 to 999 seconds in ones digit, the decimal point is 0 to 99.9 seconds in ten digits, and the decimal point is 0 to 999 minutes; the time is set.<br>2.Digital Display Delay Controller：(DC 12V 3 Button）<br>Product parameters<br>Working voltage: DC12V (normal working voltage DC10V-16V)<br>Source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)<br>Output capability: It can control devices within 30v5A or within 220v5A<br>Quiescent current: 20mA, working current: 50mA<br>Service life: more than 100,000 times;<br>Working temperature: -40~85 °C;<br>Net weight: about 26g<br>Size: 64.2mm*34.8mm*18.5mm<br>Features<br>Voltage input anti-reverse circuit, worry-free wiring. Signal input optocoupler isolation, strong anti-interference ability. Set the parameter to power off permanent memory. Powerful flash MCU online programming function, according to user needs can contact the manufacturer to customize the required functions.<br>Wiring diagram<br>Function introduction<br>P-1: The signal triggers the relay to pull in. When the time is up, the relay is disconnected during the delay.<br>A: Invalid trigger again B: Re-trigger re-clocking C: Trigger relay reset again to stop timing<br>P-2: The signal trigger start timing time T1, the time is up to the relay pull-in time T2 is disconnected (reset)<br>A: Invalid trigger again B: Re-trigger re-clocking C: Start delay without triggering power-on<br>P-3: Cycling: Turn on T1, disconnect T2, infinite loop. For T1 and T2, the time is adjustable; if a parameter is turned ON or OFF, it can be turned on or the power is turned on.<br>A: The relay is turned on immediately after power-on. B: The relay is turned off and then turned on after power-on.<br>P-4: There is signal, the relay is closed, the suction is kept, the signal disappears, the timing starts, the time is up, the relay is disconnected, during the delay, the signal is given again, the delay is cancelled, the relay is kept, the signal disappears, and the time is re-timed.<br>Notes<br>The relay output is a passive contact that has no live output and controls the on/off of a line.<br>3.Digital Display Delay Controller：<br>(DC 12V with Buzzer 3 Button)<br>Product parameters<br>Working voltage: DC12V (normal working voltage DC10V-16V)<br>Source: DC4V~20V (usual power supply positive trigger, button, PNP sensor, PLC signal, etc.)<br>Output capability: It can control devices within 30v5A or within 220v5A<br>Quiescent current: 20mA, working current: 50mA<br>Service life: more than 100,000 ti